A room that never quite warms up, a curtain that moves when the windows are shut, a chilly strip of floor by the front door: these are drafts, and they cost comfort and money all winter and, in reverse, all summer. The good news is that most air leaks are small, obvious once found, and fixed with a few inexpensive materials.

The process is simple. Find the leaks first, then seal the biggest ones, starting with the places air moves most.

Why Drafts Happen

Houses shift, seals dry out, and gaps open where different materials meet. Warm air rises and escapes high in the house, which pulls cold air in through gaps low down. That is why you often feel the draft at your ankles. The usual suspects are:

  • The bottom and sides of exterior doors, where old weatherstripping flattens or cracks.
  • Window sashes and frames, especially where the window slides or the caulk has pulled away.
  • Outlets and switches on exterior walls, which have no insulation behind the cover plate.
  • Mail slots, pet doors, and attic hatches.
  • Gaps where pipes and cables enter the house.

Find the Leaks First

Pick a cool, breezy day and close all the windows and doors. Then try one of these low-tech tests:

  1. The hand test. Slowly pass a damp hand along the edges of doors and windows. Moisture makes air movement feel much stronger.
  2. The tissue test. Hold a strip of tissue or a thin ribbon near a suspect edge. If it flutters or leans, air is moving.
  3. The light test. At night, have someone shine a flashlight around the outside edge of a closed door while you look from inside. Any visible light is a gap.
  4. The dollar-bill test. Close a door or window on a bill. If it slides out with no resistance, the seal is loose.

Mark each spot with a small piece of painter’s tape so you can work through them in one pass.

Where drafts usually sneak in: under the door, around window sashes, and through outlets on exterior walls.

Seal Doors

Doors usually leak the most air, and the fixes are quick:

  • Replace worn weatherstripping around the frame with adhesive foam or a rubber strip. Clean the surface first so it sticks, and press it so the door compresses it slightly when closed.
  • Add a door sweep to the bottom edge. A screw-on or adhesive sweep closes the gap above the threshold.
  • Use a draft stopper in a pinch. A rolled towel or a fabric tube across the base of the door blocks air right away, and it is easy to remove.
  • Tighten the hinges and strike plate if the door sits loosely in the frame.

Seal Windows

Match the fix to the kind of gap:

  • Fixed gaps (cracks between frame and wall): caulk them. Use a flexible, paintable caulk made for windows, and remove old, crumbly caulk first.
  • Moving parts (sashes that slide): use self-adhesive foam tape or a V-shaped strip so the window can still open.
  • Old single-pane glass: a clear shrink-film kit applied to the inside of the frame adds an insulating air layer for the cold months. Remove it in spring.
  • Heavy curtains add a bit of insulation on winter nights. Open them on sunny days to let the warmth in.

Don’t Forget the Small Holes

Outlet and switch plates on exterior walls leak surprisingly well. Foam gaskets cost little and slip in behind the cover plate. Switch the power off at the breaker before you take the plate off. Use expanding spray foam for larger gaps where pipes or cables pass through a wall, and a cover or plug for a mail slot you do not use. Leave any vents your heating and appliances need to breathe: sealing a house is about stopping stray air, not blocking intentional airflow.

Keep It Working

  • Re-test every fall before the cold arrives. Weatherstripping wears out over a few seasons.
  • Keep moisture in mind. A tighter home holds more humidity, so use bathroom and kitchen fans.
  • Start with the worst leak rather than sealing everything at once. A single door often makes the biggest difference.
TLDR / Start hereClose everything up on a breezy day and hunt for drafts with a damp hand or a strip of tissue. Seal the door first with fresh weatherstripping and a sweep, caulk fixed window gaps, add foam gaskets behind exterior outlet plates, and re-check each fall.